Traxxas Ez Peak Charger Not Recognizing Battery?

If your Traxxas Ez Peak charger isn’t recognizing your battery, there are a few things you can try. First, make sure that the battery is properly connected to the charger. If the connections are loose, it can cause the charger to not work correctly.

Also, check to see if the battery is fully charged. If it’s not, then charge it for a few hours before trying again. Finally, if none of these solutions work, you may need to replace the battery.

If your Traxxas Ez Peak charger is not recognizing your battery, there are a few things you can try. First, make sure that the battery is properly connected to the charger. Next, check to see if the battery is damaged or defective.

If neither of these solutions work, then you may need to contact Traxxas customer service for further assistance.

Traxxas Ez Peak Charger Not Recognizing Battery?


Why is My Traxxas Ez Peak Charger Blinking Red?

If your Traxxas EZ peak charger is blinking red, it means that the charger is not receiving power. This could be caused by a number of things, including: -A loose connection between the charger and the power source

-A faulty power source -A damaged charger If you suspect that the problem is with the charger, first check all of the connections to make sure they are tight.

If that does not solve the problem, try using a different power source. If the charger still does not work, it may need to be replaced.

How Do You Charge a Non-Traxxas Battery on a Traxxas Ez Peak Plus?

If you have a Traxxas EZ peak plus charger, you can charge a non-Traxxas battery by following these steps: 1. Connect the charger to the battery. 2. Set the switch on the charger to “NiMH” or “LiPo”, depending on the type of battery you are charging.

3. Set the voltage to match the voltage of the battery you are charging. For example, if you are charging a 7.4 volt LiPo battery, set the voltage to 7.4 volts on the charger. 4. Set the current limit to 1 amp for NiMH batteries, or 3 amps for LiPo batteries.

How Do I Charge My Lipo Battery With Ez Peak Plus?

Lipo batteries are a type of rechargeable battery that is commonly used in RC vehicles. They are typically made up of two or three cells, each of which needs to be charged separately. The EZ peak plus is a charger that is specifically designed for lipo batteries.

It can charge all types of lipo batteries, including 2S, 3S, and 4S packs. To charge your lipo battery with the EZ peak plus, first make sure that the charger is properly plugged into an outlet and that the power switch is in the ON position. Then, connect your battery to the charger using the appropriate adapter cable.

Once the battery is connected, press the START button on the charger and wait for the charging process to begin. The EZ peak plus will automatically stop charging when the lipo battery is full. At this point, you can disconnect the battery from the charger and use it as normal.

How Do I Know When My Traxxas Ez Peak is Charged?

When your Traxxas EZ Peak is charging, the LED on the charger will be red. Once it reaches full charge, the LED will turn green.

Ez peak charger won't recognize battery? Here is how to fix it.

Traxxas Ez Peak Charger All Lights Flashing

If you own a Traxxas Ez Peak charger, you may have noticed that all the lights on the charger are flashing. This is normal behavior and indicates that the charger is in protection mode. When the charger is first plugged in, all the lights will flash for about 2 seconds.

After that, only the green light will remain lit, indicating that the charger is ready to use.

Traxxas Battery Too Low to Charge

If you’re anything like me, you love your Traxxas RC car. You take it out to the track or the local park and race around for hours, enjoying every minute. But there’s one problem – eventually, the battery will run low and you’ll need to recharge it.

However, if the battery is too low, you may not be able to charge it back up again. This can be frustrating, especially if you’re in the middle of a race or a session. So what do you do if your Traxxas battery is too low to charge?

First of all, don’t panic! There are a few things you can try before giving up hope. One option is to use a higher-voltage charger.

If your standard charger isn’t working, try swapping it out for a more powerful one. This may be enough to get the job done. Another possibility is to connect multiple batteries in parallel.

This will increase the overall voltage and may be enough to get your Traxxas car up and running again. Finally, if all else fails, you can always send your car back to Traxxas for service. They’ll likely be able to fix the problem and get you back on track in no time!

Traxxas Ez-Peak Charger Error Codes

If you’re a Traxxas fan, then you’re probably familiar with their line of EZ-Peak chargers. These handy devices are great for quickly and easily charging your Traxxas batteries. But what do you do if you get an error code on your charger?

There are four main error codes that can appear on your Traxxas EZ-Peak charger: Error 1: This means that the charger is not receiving power from the AC adapter. Make sure that the AC adapter is properly plugged into an outlet and that the charger is correctly plugged into the adapter.

Error 2: This indicates that there is a problem with the battery pack being charged. Try using a different battery pack to see if the error persists. If it does, there may be an issue with the charger itself and you should contact Traxxas customer support for assistance.

Error 3: This means that the temperature of either the charger or battery pack is too high. Make sure that both the charger and battery pack are in a well-ventilated area and not in direct sunlight. If the problem persists, try charging at a lower Amp rate to reduce heat build-up.

Error 4: This indicates that there is something wrong with one of the charge leads. Check all of the connections to make sure they are secure and free of any corrosion or debris. If everything looks good, try replacing one of the charge leads to see if that resolves the issue.

Hopefully this article has helped you understand what those pesky error codes mean on your Traxxas EZ-Peak charger!

Traxxas Ez Peak Charger Fuse

If you’re in the market for a new charger for your RC batteries, you may be wondering if the Traxxas EZ Peak Charger is worth the investment. This charger is one of the most popular on the market, and for good reason – it’s simple to use and extremely reliable. In this blog post, we’ll take a closer look at the features of the Traxxas EZ Peak Charger and see if it’s right for you.

The Traxxas EZ Peak Charger is a NiMH/LiPo compatible charger that can charge 2-4 cell batteries. It has two independent charging ports so that you can charge multiple batteries at once, and it also features an integrated balance port for LiPo batteries. The charger includes four different adapter plugs to fit a variety of battery types, and it has an LED indicator light to let you know when your batteries are fully charged.

One of the best features of the Traxxas EZ Peak Charger is its built-in safety features. If there is ever an issue with your battery during charging, the charger will automatically shut off to prevent damage. This makes it one of the safest chargers on the market – perfect for those who are new to RC or don’t want to worry about their batteries getting damaged.

So, should you buy the Traxxas EZ Peak Charger? If you’re looking for a reliable and safe charger that can handle multiple battery types, then yes – it’s definitely worth considering. It’s easy to use and comes with all of the necessary adapters, making it a great choice for both beginners and experienced RC enthusiasts alike.


If your Traxxas EZ Peak charger is not recognizing your battery, there are a few things you can try. First, make sure that the battery is fully charged. If it is, then try disconnecting and reconnecting the battery to the charger.

You may also need to reset the charger by unplugging it and plugging it back in. If none of these things work, then you may need to replace your battery.

Michael Sayers

Hi, this is your friend Michael Sayers. I’m an automobile engineer, but I have become an expert on RC cars. Seems funny to you! After graduating in automobile engineering, I worked for a renowned car manufacturing company for six months only. A few months later, I joined a popular RC vehicle manufacturing company as a quality in charge. However, I’ve created this site Altimarc, to share my decade of experience with people looking for an RC vehicle who don’t have adequate knowledge about that.

Recent Posts