If your RC car is bouncing around too much, it might be time to replace the shocks. This can be a difficult task, but with these steps you’ll be able to do it in no time.
To start, you’ll need to remove the old shocks from your car.
This can be done by taking off the wheels and then unscrewing the shocks from their mounts. Once they’re off, you can put on the new shocks by screwing them into place.
Make sure that the new shocks are screwed in tight so that they don’t come loose while you’re driving.
Also, check to see if the shock oil needs to be replaced. If it does, simply unscrew the top of the shock and pour out the old oil. Then, fill it up with new oil and screw the top back on.
- Remove the screws that hold the shocks in place on the RC car
- Pull out the old shocks and insert new ones in their place
- Screw the new shocks into place
- Test drive the RC car to make sure the new shocks are working properly

Credit: www.instructables.com
Contents
- How Do You Change Shocks on a Remote Control Car?
- How Do You Install Rc Shocks?
- How Do I Change the Springs on My Rc Shocks?
- How Much Does It Cost to Fill Rc Shocks?
- How To change Rc Car Shock Oils
- How Much Oil in Rc Shocks
- Rc Shock Maintenance
- Filling Rc Crawler Shocks
- How to Rebuild Shocks
- Conclusion
How Do You Change Shocks on a Remote Control Car?
Assuming you would like a blog post on how to change the shocks on a remote control (RC) car:
“How to Change Shocks on a Remote Control Car”
Just like their full-size counterparts, RC cars need periodic maintenance to keep them running smoothly.
One of the most important parts of an RC car is the suspension, and specifically the shocks. Over time, these can become worn out or damaged, and will need to be replaced. Here’s a step-by-step guide on how to change the shocks on your remote control car.
Tools and Materials Needed:
-Replacement shocks for your specific RC car model
-Hex wrench set
-Shock oil (optional)
-Spray lubricant (optional)
Instructions:
1. Begin by lifting up your RC car so that you can access the underside. You may need to remove some body panels in order to do this – consult your owner’s manual for guidance.
2. Once you have access to the suspension, locate the screws that hold the shock in place.
These will typically be located at the top and bottom of each shock absorber. Use your hex wrench set to loosen and remove these screws.
3. Gently pull out the old shock absorbers from their mounts.
If they are stuck, you can use a spray lubricant such as WD-40 to help loosen them up.
4.. Take your replacement shocks and line them up with their respective mounts.. Screw in the new shocks using your hex wrench set, making sure not to overtighten them..
5.(Optional) If desired, you can add shock oil to your new shocks before installing them.. This helps protect against wear and tear and makes for a smoother ride.. Be sure not follow the manufacturer’s instructions when adding oil – too much can damage your shocks..
6.(Optional) Once everything is back in place, give your RC car a test run around your track or neighborhood.. You should immediately notice an improvement in handling thanks to those fresh new shocks!
How Do You Install Rc Shocks?
Installing RC shocks is a relatively easy process, but there are a few things you need to know before you get started. Here’s a quick guide to installing RC shocks:
1. Read the instructions that come with your shocks carefully.
This will give you an idea of what parts you need and how the installation process works.
2. Gather all the tools and materials you need before starting the installation. This will make the process go more smoothly and help you avoid any mistakes.
3. Follow the instructions step by step to install your shocks correctly. Pay close attention to all the details so that everything fits together properly.
4. Once your shocks are installed, test them out to make sure they’re working properly.
Start by slowly driving over some bumps to see how they respond. If everything feels good, then you’re all set!
How Do I Change the Springs on My Rc Shocks?
If your RC car’s shocks are not performing as they should, it may be time to replace the springs. In this blog post, we will show you how to change the springs on your RC shocks.
First, you will need to remove the old springs from the shocks.
To do this, simply unscrew the retaining cap at the top of the shock and pull out the spring. Next, take your new springs and insert them into the shock, making sure that they are properly seated in the bottom cup. Finally, screw on the retaining cap and compress the shock to check that everything is secure.
Now that you know how to change the springs on your RC shocks, you can keep your car running smoothly and efficiently for years to come!
How Much Does It Cost to Fill Rc Shocks?
It can cost anywhere from $20 to $100+ to fill RC shocks, depending on the size of the shocks and how much oil is needed. Many hobby shops will charge by the ounce for shock oil, so it is important to know how much oil your shocks hold before heading to the shop. Generally, smaller shocks will need less oil and therefore be less expensive to fill.
How To change Rc Car Shock Oils
How Much Oil in Rc Shocks
If you are a radio controlled (RC) enthusiast, then you know that one of the most important things to keep an eye on is your RC’s shocks. Shocks play a vital role in how your RC handles and performs, and as such, it is important to make sure they are always in good condition. But how much oil should you put in your RC shocks?
This is actually a fairly common question among RC enthusiasts, as there is no one-size-fits-all answer. The amount of oil you should use in your shocks will depend on a number of factors, including the type of vehicle you have, the terrain you will be driving on, and your personal preferences.
That being said, there are some general guidelines you can follow when it comes to adding oil to your shocks.
For example, most experts recommend using between 10 and 30wt oil for buggy shocks, and between 30 and 60wt oil for truck shocks. Start with the lower end of the range and increase the weight if needed until you find the right balance for your vehicle.
As always, experiment until you find what works best for you and your setup!
Rc Shock Maintenance
If you’re a fan of RC cars, then you know that keeping your shocks in good condition is important for both performance and safety. Here are some tips on how to maintain your RC shocks:
1. Check the shocks regularly for leaks or damage.
If you notice any issues, replace the shocks immediately.
2. When cleaning your RC car, be sure to clean the shocks as well. This will help keep them in good working condition.
3. If you’re not using your RC car for a while, it’s a good idea to remove the shocks and store them in a cool, dry place. This will prevent them from becoming damaged or warped over time.
By following these simple tips, you can keep your RC shocks in great shape and ensure that your car performs at its best!
Filling Rc Crawler Shocks
If you’re into rock crawling, then you know that having properly filled shocks is essential to your success. Here’s a quick guide on how to fill your RC crawler shocks so that you can get the most out of them.
First, make sure that your shocks are clean and free of any dirt or debris.
Next, using a shock pump, fill each shock with oil until it reaches the bottom of the threads. Once the shocks are full, compress each one fully and release slowly several times to bleed the air out of the system.
Now it’s time to add weight.
For this, you’ll need to use either lead shot or BBs. Add enough weight so that when the shock is fully compressed, there is still a slight bit of resistance. This will help ensure that your shocks are able to properly absorb impacts and prevent bottoming out.
With your shocks filled and weighted appropriately, you’re now ready to tackle any terrain that comes your way!
How to Rebuild Shocks
If your car’s shocks are worn out, you’ll notice a difference in the ride. It may feel like the car is bouncing or floating over bumps, and you may even see increased wear on your tires. Rebuilding shocks is not a difficult task, but it does require some basic mechanical skills.
Here’s a step-by-step guide to rebuilding shocks:
1. Remove the old shock absorber from the car. This will usually involve removing a few bolts that hold it in place.
2. disassemble the shock absorber by unscrewing the cap at one end. Be careful not to lose any of the internal parts.
3. Inspect all of the parts for wear and damage.
If any parts are damaged, they will need to be replaced before reassembling the shock absorber.
4. Clean all of the parts with brake cleaner or another suitable solvent. This will remove any dirt and grime that could cause problems during reassembly.
5 . Reassemble the shock absorber, being sure to put all of the parts back in their proper places . Tighten all of The caps and bolts securely before installing The shock back onto The car .
Refer to your vehicle’s service manual for specific instructions on how to do this .
By following these steps , you can rebuild your own shocks and save yourself some money .
Conclusion
If your RC car is starting to feel a little sluggish, it might be time to change the shocks. Here’s a quick guide on how to do it:
1. First, you’ll need to remove the old shocks.
To do this, simply unscrew the screws that hold them in place.
2. Next, take your new shocks and screw them into place. Make sure they’re tight so they don’t come loose while you’re driving.
3. Finally, test out your car to see how it feels. You should notice a difference in the way it handles and drives.