How to Change Pinion Gear on Traxxas Stampede?

The Traxxas Stampede is a great RC truck that can handle a lot of abuse. But like any RC vehicle, it will eventually need some maintenance. One of the most common maintenance items is changing the pinion gear.

This guide will show you how to change the pinion gear on your Traxxas Stampede.

  • Traxxas Stampede is a great remote control truck that many people enjoy
  • In order to change the pinion gear, first remove the old one by unscrewing it from the motor shaft
  • Next, take the new pinion gear and screw it onto the shaft in its place
  • Be sure to tighten it securely so that it doesn’t come loose while in use
  • That’s all there is to changing the pinion gear on a Traxxas Stampede!

How to change your Pinion Gear on a Traxxas Stampede 2wd

How Do I Change the Spur Gear on My Stampede?

If you’re looking to change the spur gear on your Stampede, here’s what you’ll need to do: 1. Remove the body from the chassis. This will give you access to the transmission.

2. Unscrew and remove the old spur gear from the transmission shaft. 3. Screw on the new spur gear onto the transmission shaft. Make sure it’s tight and secure before moving on.

4. Reattach the body to the chassis and screw it in place.

How Do You Install Traxxas Pinion Gear?

Installing a pinion gear on a Traxxas model is a simple process that can be completed in just a few minutes. The first step is to remove the old pinion gear from the motor shaft. This can be done by unscrewing the setscrew from the shaft and pulling the gear off.

Next, take the new pinion gear and slide it onto the motor shaft. Be sure that the teeth of the gear are properly aligned with those of the spur gear before tightening down the setscrew. Once everything is tightened up, your model should be ready to run!

How Do I Change My Rc Pinion Gear?

If you’re wondering how to change your RC pinion gear, the process is actually quite simple. All you need is a hex key and a few minutes of time. Here’s a step-by-step guide on how to do it:

1. First, remove the battery from your RC car. This will make it easier to access the parts you need to change. 2. Next, use a hex key to loosen the set screw that holds the pinion gear in place.

Keep in mind that left-handed threads are used on many RC cars, so be sure to turn the hex key counter-clockwise when loosening the set screw. 3. Once the set screw is loose, carefully remove the old pinion gear from the shaft. 4. To install the new pinion gear, simply slide it onto the shaft and tighten down the set screw with your hex key.

Be sure not to overtighten as this can strip out the threading or damage the gear itself. 5. That’s it!

Which Pinion Gear is Faster?

Pinion gears are used in a wide variety of applications, from automotive to industrial settings. But which pinion gear is faster? The answer may surprise you.

Pinion gears come in two basic types: straight cut and helical. Straight cut pinion gears are typically faster than helical gears because they have fewer teeth that need to engage with the gearwheel. This makes them less likely to slip, which can happen with helical gears when they are under load.

However, there are some drawbacks to straight cut pinion gears. They tend to be noisier than helical gears and can produce more vibration. They also wear out more quickly and are not as strong as helical Gears.

If you need a durable, long-lasting pinion gear, then a helical gear is a better choice. However, if you need a fast, efficient pinion gear, then a straight cut gear is the way to go.

How to Change Pinion Gear on Traxxas Stampede?

Credit: www.ebay.com

How to Change Pinion Gear on Traxxas Slash 2Wd

If you’re looking to change the pinion gear on your Traxxas Slash 2Wd, here’s what you need to do. First, remove the old pinion gear by unscrewing it from the motor shaft. Next, take your new pinion gear and thread it onto the motor shaft.

Make sure that it is tight and secure before moving on. Finally, reattach the axle shaft to the differential and screw it back into place. That’s all there is to it!

After following these steps, your Traxxas Slash 2Wd will be good as new.

How to Change Pinion Gear on Traxxas Rustler 2Wd

If you’re looking to change the pinion gear on your Traxxas Rustler 2WD, there are a few things you’ll need to do. First, remove the old pinion gear by taking out the four screws that hold it in place. Next, take your new pinion gear and line it up with the holes in the motor.

Once it’s lined up, screw it in place with the four screws. Finally, replace the axle nut and washer to secure everything in place. That’s all there is to it!

With a few simple steps, you can easily change the pinion gear on your Traxxas Rustler 2WD.

How to Change Spur Gear on Traxxas Slash 2Wd

If you’re looking to change the spur gear on your Traxxas Slash 2Wd, here’s what you’ll need to do. First, remove the pinion gear from the motor. Next, remove the set screw from the spur gear.

With the set screw removed, you’ll be able to pull the spur gear off of the axle. To install the new spur gear, simply line it up on the axle and press it into place. Once it’s seated properly, replace the set screw and tighten it down.

Finally, re-install the pinion gear onto the motor shaft. That’s all there is to it! With a new spur gear in place, your Traxxas Slash 2Wd will be ready to hit the track and tear up some serious terrain.

Conclusion

In order to change the pinion gear on your Traxxas Stampede, you will first need to remove the old one. To do this, you will need to use a hex wrench to loosen the set screw that is holding it in place. Once the set screw has been removed, you can simply pull the old pinion gear off of the motor shaft.

Next, take your new pinion gear and align it with the holes on the motor shaft. Once it is lined up correctly, use your hex wrench to tighten down the set screw so that it is snug against the motor shaft. Be sure not to overtighten as this could damage both the pinion gear and the motor shaft itself.

With the new pinion gear in place, reattach any other parts that were removed during disassembly (such as the gears or drivetrain components) and your Traxxas Stampede should be ready to hit the trails once again!

Michael Sayers

Hi, this is your friend Michael Sayers. I’m an automobile engineer, but I have become an expert on RC cars. Seems funny to you! After graduating in automobile engineering, I worked for a renowned car manufacturing company for six months only. A few months later, I joined a popular RC vehicle manufacturing company as a quality in charge. However, I’ve created this site Altimarc, to share my decade of experience with people looking for an RC vehicle who don’t have adequate knowledge about that.

Recent Posts