If you’re new to the world of RC cars, then you might be wondering how to break in a brushed RC car motor. Here’s a quick guide on how to do it. First, make sure that your motor is properly lubricated.
You can do this by using a good quality motor oil. Next, run the motor at low speeds for about 15 minutes. This will help the brushes and commutator get used to each other and start working together properly.
Finally, increase the speed gradually over the next few days until you reach the maximum speed that your motor can handle.
Contents
- How To Break In Your brushed motor
- Do You Have to Break in a Brushed Rc Motor
- How to Break in a Brushless Rc Motor
- How to Make a Brushed Motor Faster
- How to Break in a Hawk 7 Motor
- Traxxas Brushed Motor Break in
- How Do You Break in a Brushed Rc Motor?
- Should You Break in Brushed Rc Motor?
- How Do You Break in New Motor Brushes?
- Do I Need to Break in My Rc Motor?
- Conclusion
How To Break In Your brushed motor
- Charge the battery: Make sure that your brushless RC car has a full charge before attempting to break in the motor
- This will help prevent any damage to the motor from overworking it
- Start slow: Once the battery is charged, slowly start to increase the speed of the motor
- Do not go full throttle right away, as this can damage the motor
- Increase speed gradually: Continue to increase the speed of the motor in small increments until you reach half throttle or three-quarter throttle
- At this point, you can begin to slowly increase the amount of time that you run at each throttle setting
- Don’t overdo it: It is important not to overwork the motor during the break-in process
- Allow it to cool down after each run and do not exceed 10 minutes of total running time during the first day of use
Do You Have to Break in a Brushed Rc Motor
If you’re new to the world of RC, you may be wondering if you need to break in your brushed RC motor. The answer is yes! Breaking in your motor will help ensure that it runs smoothly and efficiently for years to come.
Here’s how to do it:
1. Start by running the motor at low speeds for about 15 minutes. This will help loosen up the brushes and allow them to seat properly against the commutator.
2. Next, increase the speed gradually over a period of about 30 minutes. Make sure not to go too fast too soon – you don’t want to overheat the motor.
3. Once you’ve reached full speed, let the motor cool down for about 15 minutes before shutting it off completely.
Breaking in your brushed RC motor may seem like a lot of work, but it’s definitely worth it! By following these simple steps, you’ll extend the life of your motor and keep it running smoothly for years to come.
How to Break in a Brushless Rc Motor
If you’re new to the world of brushless RC motors, you might be wondering how to break in your new motor. Here’s a quick guide on how to do just that.
First things first, what is breaking in a motor and why do you need to do it?
Breaking in a motor essentially means running it at lower speeds and under less load than normal operation. This helps the motor run smoother and last longer. It also allows the bearings and other moving parts to seat properly and reduces overall wear and tear.
So how do you break in a brushless RC motor? There are a few different methods, but here’s one that’s pretty simple and straightforward.
1) Start by connecting your motor to a low voltage power source, like a 3s lipo battery.
You don’t want to use too much power or go too fast right away, so keep things slow at first.
2) Once your motor is connected, slowly increase the throttle until the motor reaches its maximum RPM. Keep it there for about 30 seconds, then reduce the throttle back down to zero.
Repeat this step 2-3 times.
3) Next, gradually increase the load on the motor by adding weight or resistance. This could mean attaching a prop or wheels if your motor is for an airplane or car, or adding weight to the shaft if it’s for a boat or helicopter.
Again, slowly increase throttle until maximum RPM is reached before reducing back down to zero throttle. Repeat 2-3 times as needed.
After following these steps, your brushless RC motor should be good to go!
How to Make a Brushed Motor Faster
Making a brushed motor faster is relatively easy and only requires a few basic tools. The most important tool you will need is a good quality drill. Other than that, all you need is a screwdriver, some sandpaper, and some patience.
The first step is to remove the end caps from the motor. Be careful not to damage the wires leading into the motor. Once the end caps are off, take a look at the brushes.
If they are worn down, replace them with new ones.
Next, use the drill to enlarge the holes in the commutator. This will allow more current to flow through the brushes and make the motor spin faster.
Be sure not to enlarge the holes too much or they will become oval shaped and cause problems.
Once you have enlarged the commutator holes, reassemble the motor and test it out. If it still isn’t going as fast as you would like, there are a few other things you can try.
One is to sand down any raised edges on the inside of the housing where the brushes ride. This will help them make better contact withthe commutator and spin faster.
Another thing you can try is increasing th e voltage that’s going tothe motor .
This w il l make it draw more currentand spin faster , but be careful notto overdo it or you could burn outthe motor . Start with just a small increaseand go from there .
With these tips , you should be ableto get your brushed motorspinning quite a bit faster in no time !
How to Break in a Hawk 7 Motor
Assuming you would like a blog post about how to break in a Hawk 7 motor:
If you’ve just purchased a Hawk 7 motor, congratulations! You’re now the proud owner of one of the most popular and reliable motors on the market.
But before you can start enjoying all that your new motor has to offer, there’s one important task left to do: breaking it in.
Breaking in a new engine is crucial to ensuring its long-term health and performance. It allows all the internal components to wear in and seat properly, which reduces friction and increases efficiency.
Plus, it helps ensure that your engine will have a long and happy life.
So how do you go about breaking in your new Hawk 7 motor? Here are some simple steps to follow:
1) Before starting your engine for the first time, make sure all the fluids are at the correct levels. This includes oil, coolant, and fuel. Check your owner’s manual for specific recommendations.
2) Start the engine and let it idle for 15-20 minutes. Do not rev the engine during this time. Letting it idle will allow all the moving parts to get lubricated without putting too much stress on them.
3) Once the initial idling period is over, slowly bring up the RPMs while keeping a close eye on the temperature gauge. You don’t want to overheat your engine, so keep an eye out for any warning signs (i.e., rising temperatures). Slowly increase speed until you reach about half of what your maximum RPMs will be when fully broken in .
For example , if your max RPMs is 6000 , then only run at around 3000 RPMs during this phase of breaking in . Take care not cause excessive load or strain on newly seated components . Back off immediately if temperatures begin to rise excessively . Letting your motor cool down completely between high load periods is also critical during this phase . Repeat this process – slowly increasing speed while monitoring temperature – until you reach 3-4 hours of total running time . At this point , your Hawk 7 should be sufficiently broken -in and ready for regular use . Following these simple steps will help ensure that your new motor has a long and healthy life !
Traxxas Brushed Motor Break in
If you’re new to the world of RC cars, you’ve probably heard about brushed motors. These are the most common type of motor used in RC cars, and they’re relatively easy to break in. Here’s a quick guide on how to properly break in your Traxxas brushed motor.
The first thing you’ll need to do is find a good place to run your car. Somewhere with smooth pavement is ideal. Once you’ve found a good spot, it’s time to start the break-in process.
Start by running your car at half throttle for around 15 minutes. This will help wear in the brushes and commutator. After 15 minutes, stop the car and let it cool down for a few minutes.
Next, increase the throttle to 3/4 throttle and run for another 15 minutes. Again, stop the car and let it cool down before proceeding.
Finally, run at full throttle for 5-10 minutes.
This will help seat the brushes and commutator into their final positions. After this final step, your motor should be fully broken in and ready for regular use!

Credit: www.rccaraction.com
How Do You Break in a Brushed Rc Motor?
Assuming you are referring to a brushed RC motor that is new and needs to be broken in:
The first step is to find an area where the motor can be run without any load. This can be done by removing the pinion gear from the motor.
Once the pinion is removed, connect the battery pack to the ESC and turn on the power switch. The motor should now run without resistance. If it does not, check your connections and make sure everything is plugged in correctly.
Next, slowly increase the throttle until the motor reaches half speed. Allow it to run at half speed for about five minutes before increasing the throttle again. Continue this process until the motor reaches full speed.
At this point, allow the motor to cool for a few minutes before repeating the process from step two.
After following these steps a few times, your brushed RC motor should be broken in and ready to use!
Should You Break in Brushed Rc Motor?
No, you should not break in a brushed RC motor. Doing so can damage the motor and decrease its lifespan.
How Do You Break in New Motor Brushes?
If your motor brushes are worn out, you’ll need to replace them. But first, you’ll need to break in the new ones. Here’s how:
1. Start by trimming the bristles on the new brush so they’re flush with the metal housing. This will help ensure good contact between the brush and the commutator.
2. Install the new brush in the motor, making sure it’s seated properly in the holder.
3. Apply a small amount of conductive grease to the ends of the brush where it contacts the commutator. This will help carry electrical current and also prevent corrosion.
4. Reconnect power to the motor and start it up.
Let it run for a few minutes so that the new brush can start working with the commutator surface.
Do I Need to Break in My Rc Motor?
If you’ve just purchased a new RC motor, you might be wondering if you need to break it in before using it. The answer is yes, you should definitely break in your new RC motor! Here’s why:
When you first start up a new RC motor, it’s not running at its full potential. The bearings and other parts are still tight and need to be loosened up. Running the motor without breaking it in first can damage the internals and shorten its lifespan.
Breaking in your RC motor is actually pretty easy to do. Just run it at about 75% throttle for 15 minutes or so. This will help loosen up the internals and get everything moving smoothly.
After that, your RC motor will be good to go and will last for many hours of fun!
Conclusion
If you’re new to the world of brushed RC cars, then you might be wondering how to break in a brushed motor. Here’s a quick guide on how to do just that.
Breaking in a brushed motor is important because it allows the motor to reach its full potential and prevents damage from occurring too early on.
There are two main methods for breaking in a motor: running it at low speeds or using an ESC with a built-in brake.
Running the motor at low speeds is the most common method and is pretty self-explanatory. You’ll just need to run the car at lower speeds for extended periods of time until the motor is broken in.
The second method, which is often considered more effective, is using an ESC with a built-in brake. This works by applying light pressure to the brakes while the motor is running, which helps seat the brushes properly and break them in faster.